Search Results

A standard port fuel injected, unthrottled single cylinder four-stroke SI engine, with a compression ratio of 10.3:1, and using standard gasoline fuel, has been adapted to operate in the homogeneous charge compression ignition (HCCI) mode, by modifying the valve timing. It has been found that over a speed range of between 1300 and 2000 rpm, and lambda values of between 0.95 and 1.1, stable operation is achieved without spark ignition. The internal EGR rate was estimated to be about 60%, and emissions of NOX were typically 0.25 g/kWh. Practical implementation of this HCCI concept will require variable valve timing, which will also enable reversion to standard SI operation for maximum power.

Analytical procedures for the speciation of hydrocarbons and oxygenates (ethers, aldehydes, ketones and alcohols) in vehicle evaporative and tailpipe exhaust emissions have been improved for Phase II studies of the Auto/Oil Air Quality Improvement Research Program (AQIRP). One gas chromatograph (GC) was used for measurement of C1-C4 species and a second GC for C4-C12 species. Detection limits for this technique are 0.005 ppm C or 0.1 mg/mile exhaust emission level at a chromatographic signal-to-noise ratio of 3/1, a ten-fold improvement over the Phase I technique. The Phase I library was modified to include additional species for a total of 154 species. A 23-component gas standard was used to establish a calibration scale for automated computer identification of species. This method identifies 95±3% of the total hydrocarbon mass measured by GC for a typical exhaust sample. Solid adsorbent cartridges or impingers were used to collect aldehydes and ketones.

An analytical method for the determination of hydrocarbon and ether emissions from gasoline-, methanol-, and flexible-fueled vehicles is described. This method was used in Phase I of the Auto/Oil Air Quality Improvement Research Program to provide emissions data for various vehicles using individual reformulated gasolines and alternate fuels. These data would then be used for air modeling studies. Emission samples for tailpipe, evaporative, and running loss were collected in Tedlar bags. Gas chromatographic analysis of the emissions samples included 140 components (hydrocarbons, ethers, alcohols and aldehydes) between C1 and C12 in a single analysis of 54-minutes duration. Standardization, quality control procedures, and inter-laboratory comparisons developed and completed as part of this program are also described.

The Multi Material Lightweight Vehicle (MMLV), developed by Magna International and Ford Motor Company, is a result of US Department of Energy project DE-EE0005574. The project demonstrated the lightweighting potential of a five-passenger sedan while maintaining vehicle performance and occupant safety. Prototype vehicles were manufactured and limited full-vehicle testing was conducted. The Mach-I vehicle design, comprised of commercially-available materials and production processes, achieved a 364 kg (23.5%) full-vehicle mass reduction. This resulted in environmental benefits and fuel economy improvements. A significant factor in the overall MMLV mass reduction was the decrease in the powertrain system weight from 340 kg (conventional) to 267 kg (MMLV). This enabled the application of a 1.0-liter three-cylinder engine as the main powerplant. By downsizing the engine, and by implementing material changes within the engine, the weight of the dressed engine was lowered by 29 kg.

While weight reduction in automotive design and manufacturing has been on-going for several years, in the area of powertrain technology lightweighting has been a difficult challenge to overcome due to functional requirements, as well as material and manufacturing constraints. The Multi Material Lightweight Vehicle (MMLV) developed by Magna International and Ford Motor Company is a result of US Department of Energy project DE-EE0005574. The project demonstrates the lightweighting potential of a five passenger sedan, while maintaining vehicle performance and occupant safety. Prototype vehicles were manufactured and limited full vehicle testing was conducted. The Mach-I vehicle design, comprised of commercially available materials and production processes, achieved a 364kg (23.5%) full vehicle mass reduction, enabling the application of a 1.0-liter three-cylinder engine resulting in a significant environmental benefit and fuel reduction.

This paper details the lightweighting efforts of the Ford Research & Advanced Transmission team as part of the Multi Material Lightweight Vehicle Project. The Multi Material Lightweight Vehicle (MMLV) developed by Magna International and Ford Motor Company is a result of a US Department of Energy project DE-EE0005574. The project demonstrates the lightweighting potential of a five passenger sedan, while maintaining vehicle performance and occupant safety. Prototype vehicles were manufactured and limited full vehicle testing was conducted. The Mach-I vehicle design, comprised of commercially available materials and production processes, achieved a 364kg (23.5%) full vehicle mass reduction, enabling the application of a 1.0-liter three cylinder engine resulting in a significant environmental benefits and fuel consumption reduction.

The exhaust blowdown pulse from each cylinder of a multi-cylinder engine propagates through the exhaust manifold and can affect the in-cylinder pressure of other cylinders which have open exhaust valves. Depending on the firing interval between cylinders connected to the same exhaust manifold, this blowdown interference can affect the exhaust stroke pumping work and the exhaust pressure during overlap, which in turn affects the residual fraction in those cylinders. These blowdown interference effects are much greater for a turbocharged engine than for one which is naturally aspirated because the volume of the exhaust manifolds is minimized to improve turbocharger transient response and because the turbines restrict the flow out of the manifolds. The uneven firing order (intervals of 90°-180°-270°-180°) on each bank of a 90° V8 engine causes the blowdown interference effects to vary dramatically between cylinders.

A small airflow rate at engine idle is required to maintain a low engine speed and to save fuel consumption. Since the throttle plate is almost closed at idle, the plate and bore tolerance becomes important in determining the plate open area and thus the airflow rate. The objective of this work is to use computational fluid dynamics (CFD) analysis as a tool to aid throttle body design and to find out how the tolerance affects the airflow rate. Also, the conventional equation for calculating the throttle plate open area is modified to include the leakage area which is no longer negligible at idle. Throttle bodies with plate closed angles of 4.0 and 4.5 degrees under tight and loose fit conditions were studied. The flow regions above and below the plate are connected by a narrow region between the plate and the bore. This sudden change in flow area creates a big pressure loss across the plate.

A fuel fractionating system is designed and commissioned to separate standard gasoline fuel into two components by evaporation. The system is installed on a Ricardo E6 single cylinder research engine for testing purposes. Laboratory tests are carried out to determine the Research Octane Number (RON) and Motoring Octane Number (MON) of both fuel fractions. Further tests are carried out to characterize Spark-Ignition (SI) and Controlled Auto-Ignition (CAI) combustion under borderline knock conditions, and these are related to results from some primary reference fuels. SI results indicate that an increase in compression ratio of up to 1.0 may be achieved, along with better charge ignitability if this system is used with a stratified charge combustion regime. CAI results show that the two fuels exhibit similar knock-resistances over a range of operating conditions.

The worldwide automotive industry is currently preparing for a market introduction of hydrogen-fueled powertrains. These powertrains in fuel cell electric vehicles (FCEVs) offer many advantages: high efficiency, zero tailpipe emissions, reduced greenhouse gas footprint, and use of domestic and renewable energy sources. To realize these benefits, hydrogen vehicles must be competitive with conventional vehicles with regards to fueling time and vehicle range. A key to maximizing the vehicle's driving range is to ensure that the fueling process achieves a complete fill to the rated Compressed Hydrogen Storage System (CHSS) capacity. An optimal process will safely transfer the maximum amount of hydrogen to the vehicle in the shortest amount of time, while staying within the prescribed pressure, temperature, and density limits. The SAE J2601 light duty vehicle fueling standard has been developed to meet these performance objectives under all practical conditions.

Development status and insight on a “research level” piezoelectric direct injection fuel injection system for prototype hydrogen Internal Combustion Engines (ICEs) is described. Practical experience accumulated from specialized material testing, bench testing and engine operation have helped steer research efforts on the fuel injection system. Recent results from a single cylinder engine are also presented, including demonstration of 45% peak brake thermal efficiency. Developing ICEs to utilize hydrogen can result in cost effective power plants that can potentially serve the needs of a long term hydrogen roadmap. Hydrogen direct injection provides many benefits including improved volumetric efficiency, robust combustion (avoidance of pre-ignition and backfire) and significant power density advantages relative to port-injected approaches with hydrogen ICEs.

The recent trends of increasing driveline torque and use of traction control devices call for increasingly higher durability capacity from driveline components. Bench and vehicle durability tests are often used to validate designs, but they are not cost-effective and take months to complete. Traditional finite element analysis (FEA) procedures have been used effectively in the re-design of driveline components to reduce stress, and occasionally, to predict fatigue life. But in the case of certain rotating components, such as the Axle Differential Case, where the component sees large stress/strain fluctuations within the course of one complete rotation, even under constant input torque, historical fatigue analysis (when conducted) yields very conservative results. The axle differential case tends to be one of the weakest links in the rear axle assembly. Therefore, there is a crucial need for analytical methods to more accurately predict fatigue life to reduce testing time and cost.

This book presents an analysis on the potential effects of globalization on the automotive industry and the environment. Energy challenges, market economy growth, and population dynamics are considered. The authors also present future scenarios for transportation technologies to meet the ever growing global demand for transportation of goods and services while minimizing energy and environmental impacts and maximizing cost, value and widespread acceptance.

A new diesel engine, called the 6.7L Power Stroke® V-8 Turbo Diesel, and code named "Scorpion," was designed and developed by Ford Motor Company for the full-size pickup truck and light commercial vehicle markets. The combustion system includes the piston bowl, swirl level, number of nozzle holes, fuel spray angle, nozzle tip protrusion, nozzle hydraulic flow, and nozzle-hole taper. While all of these parameters could be explored through extensive hardware testing, 3-D CFD studies were utilized to quickly screen two bowl concepts and assess their sensitivities to a few of the other parameters. The two most promising bowl concepts were built into single-cylinder engines for optimization of the rest of the combustion system parameters. 1-D CFD models were used to set boundary conditions at intake valve closure for 3-D CFD which was used for the closed-cycle portion of the simulation.